Hydraulic steering help needed
Moderators: Redneck_Randy, badmoonrising, lakerunner
Hydraulic steering help needed
SO my toon steers like crap and I plan to move/rebuild a console for it
My current cable is twice as long as it needs to be and it is hard to steer because of all the bends in it.
SO I either need to figure out what I have and get a shorter cable or go Hydraulic (it steers to hard for my wife to drive it)
1000's of options for steering, where to start?
My current cable is twice as long as it needs to be and it is hard to steer because of all the bends in it.
SO I either need to figure out what I have and get a shorter cable or go Hydraulic (it steers to hard for my wife to drive it)
1000's of options for steering, where to start?
Check out "Dudes" site www.whereisdude.com
Re: Hydraulic steering help needed
So have been emailing back and forth with seastar (very helpful) BUT they have never done a mount for my engine/pontoon so they can not "recommend a kit" which from a liabilty stand point I under stand
I will look over several set ups and order parts and make a mount probably
I will look over several set ups and order parts and make a mount probably
Check out "Dudes" site www.whereisdude.com
Re: Hydraulic steering help needed
I have no experience at all with outboards - my small 115hp is my first. I want to know more about this so I will be watching and learning as usual around here!
Big and ugly but we love our 1999/2000 Crest II DL with a Yamaha F115
Re: Hydraulic steering help needed
When I went through the problem and replacement of mine, the two techs I spoke with were adamant that the cable needed to be no more than 1' longer than needed. I think you would be fine with a new steering cable of the correct length. Measuring for the correct length was not hard -- I did it a couple of different ways to make sure I was as close as I felt I could be. Measure from the motor steering rod along the length of the hull to the console, up to the helm at the wheel. Do it twice. Add 6-12".
The hardest part of all is installing the bitch! Mine was wrapped all entwined with the other electric wiring.
Just
Paul & Michele
2003 Landau DX 24' Cruise "Loretta Jane"
2003 Mercury 75hp
My Rebuild: http://pontoonforums.com/viewtopic.php?f=16&t=26135
"Don't waste brain cells over something you can do nothing about." --My Wife
2003 Landau DX 24' Cruise "Loretta Jane"
2003 Mercury 75hp
My Rebuild: http://pontoonforums.com/viewtopic.php?f=16&t=26135
"Don't waste brain cells over something you can do nothing about." --My Wife
Re: Hydraulic steering help needed
This video gave me a good understanding. The guy is boring and talks too damn much , and it's not a pontoon, but it will really help with learning the process.
https://www.youtube.com/watch?v=VJ8UruO-_a0
https://www.youtube.com/watch?v=VJ8UruO-_a0
Paul & Michele
2003 Landau DX 24' Cruise "Loretta Jane"
2003 Mercury 75hp
My Rebuild: http://pontoonforums.com/viewtopic.php?f=16&t=26135
"Don't waste brain cells over something you can do nothing about." --My Wife
2003 Landau DX 24' Cruise "Loretta Jane"
2003 Mercury 75hp
My Rebuild: http://pontoonforums.com/viewtopic.php?f=16&t=26135
"Don't waste brain cells over something you can do nothing about." --My Wife
Re: Hydraulic steering help needed
Yeah spent better part of day researching...ugh...working and I think just a new correct cable will be fine.
Been a long 4 months, nothing done on boat...hell she is dtill in the water.
Carbs drained and gas is old...and still need to do a console build and that will affect the cable length for sure.
We are working on lake side land and slip so I haven't done anything, except but new fishing licenses
Is the steering wheel taper pretty much universal?
I hate mine and a cable/helm swap will fix that with new wheel.
No mention in specs about said taper.
I drive around the lake twice a day...I miss the water, can't wait for wa weather
Been a long 4 months, nothing done on boat...hell she is dtill in the water.
Carbs drained and gas is old...and still need to do a console build and that will affect the cable length for sure.
We are working on lake side land and slip so I haven't done anything, except but new fishing licenses
Is the steering wheel taper pretty much universal?
I hate mine and a cable/helm swap will fix that with new wheel.
No mention in specs about said taper.
I drive around the lake twice a day...I miss the water, can't wait for wa weather
Check out "Dudes" site www.whereisdude.com
Re: Hydraulic steering help needed
I don't know that answer. I THINK it is. Mine was old helm off/new helm on... same wheel so no issue. The helm shaft seems pretty standard.
I hear you on the anxiousness. I look at mine hanging in the lift every day. We've had a day here & there that were very tempting to take her out, but had no water under her -- tide changes. Maybe soon.
Good luck, ol' buddy!
Paul & Michele
2003 Landau DX 24' Cruise "Loretta Jane"
2003 Mercury 75hp
My Rebuild: http://pontoonforums.com/viewtopic.php?f=16&t=26135
"Don't waste brain cells over something you can do nothing about." --My Wife
2003 Landau DX 24' Cruise "Loretta Jane"
2003 Mercury 75hp
My Rebuild: http://pontoonforums.com/viewtopic.php?f=16&t=26135
"Don't waste brain cells over something you can do nothing about." --My Wife
Re: Hydraulic steering help needed
I'm very happy with the baystar hydraulic system that came on my boat. It is rated for up to 150 hp.
2009 Sun Tracker Party Barge, NV Performance Package, 90 HP Merc 4 stroke
36 mph gps...
Cherokee Lake, Tennessee
U.S. Navy 1971-1977
36 mph gps...
Cherokee Lake, Tennessee
U.S. Navy 1971-1977
-
- Posts: 80
- Joined: Thu Mar 22, 2012 8:49 pm
Re: Hydraulic steering help needed
My old Bennington was hard to steer with my cable setup. So I went with a baystar and the change took about an hr.
Would had been faster but had a few frozen bolts. I love the feel of it. Baystar is great.
Would had been faster but had a few frozen bolts. I love the feel of it. Baystar is great.