Has anyone used the product called Krud Kutter to clean the skum line off their toons? I used it on a little area with a wet sanding block for drywall and it cleaned it pretty well however it left little scratches. I am not sure if I want to continue to use the block if it is going to leave scratches. Thought about using a plastic puddy knife like some have suggested. Any thoughts on if this would work?
Thanks,
bjb21
Cleaning Toons
Moderators: Redneck_Randy, badmoonrising, lakerunner
- nostrildomus
- Posts: 14
- Joined: Fri Aug 28, 2009 4:55 pm
- Location: Bellingham, Washington
Re: Cleaning Toons
I highly recommend JJV's Best Aluminum Cleaner: sprayed on and the waited 10 minutes; the light pressure washing.
http://www.jjvsbest.com/
I have some before and after pictures if you are interested.
KW
http://www.jjvsbest.com/
I have some before and after pictures if you are interested.
KW
2005 30' Tracker PartyHut
135hp Mercruiser I/O
Lake Samish - Bellingham, WA.
135hp Mercruiser I/O
Lake Samish - Bellingham, WA.
Re: Cleaning Toons
I was looking at that product. I have a 25' 8" Southbay.. It looks like the product is rather pricey how much can you expect to use on the toons? Pictures would be great.. Does it work as easy as they advertise?
Re: Cleaning Toons
Any time you use any type of sand paper/ block, whether it be wet or not, it's going to leave scratches. If you plan on polishing the logs, like many of us have done, then I would suggest sanding them down to as fine of sandpaper as you can find first, then polish, and protect with Sharkhide.
If you aren't worried about polishing, you can use just what others have said, or even A/C condensor coil cleaner (diluted) and it will eat away at anything that isn't aluminum, and then eventually the aluminum too if you leave it on there forever. This is what I did before I sanded and polished my logs.
If you aren't worried about polishing, you can use just what others have said, or even A/C condensor coil cleaner (diluted) and it will eat away at anything that isn't aluminum, and then eventually the aluminum too if you leave it on there forever. This is what I did before I sanded and polished my logs.
"Nauti Weasel"
2005 Beachcomber Islander 26
2005 Beachcomber Islander 26
Re: Cleaning Toons
So you would use a DA sander and then a very fine sandpaper to get the skum off then use a polish? What grit do you recommend? I have sharkhide to protect it.
Re: Cleaning Toons
The higher grit you use, the easier it will be to buff/polish. Personally, I would go to at least 1500-2000.
I polished the toons on my last boat, but haven't talked myself into tackling the tri toon yet.
I polished the toons on my last boat, but haven't talked myself into tackling the tri toon yet.
2014 Benny (Until I find a replacement for my totaled JC Tritoon)
Usually somewhere on the TN River
Usually somewhere on the TN River
- nostrildomus
- Posts: 14
- Joined: Fri Aug 28, 2009 4:55 pm
- Location: Bellingham, Washington
Re: Cleaning Toons
Here are the before and after shots; I did it exactly as easy as they showed in the video on their site:)
Still a bit wet, it was raining when I did mine:)
Still a bit wet, it was raining when I did mine:)
2005 30' Tracker PartyHut
135hp Mercruiser I/O
Lake Samish - Bellingham, WA.
135hp Mercruiser I/O
Lake Samish - Bellingham, WA.