Engine Height For 200 HP Tritoon
Moderators: Redneck_Randy, badmoonrising, lakerunner
-
- Posts: 52
- Joined: Fri Feb 24, 2017 9:17 pm
Engine Height For 200 HP Tritoon
I am trying to determine if my outboard motor is at the correct height or if I should adjust it. I have a 2006 Premier PTX 225 Legend. The boat is 22.5' long. The center tube is a full length 30" PTX toon.
The boat has a 200 HP Suzuki engine. I see 5800 RPM@ 45 MPH with a 18.5 Pitch Suzuki prop. The boat does porpoise around the upper 30's and above. This is with two people at the rear of the boat and nobody in the front lounges. Also, the 50 gallon fuel tank is near the rear of the boar in the center toon.
If I trim all the down (Negative trim) the boat does not porpoise at all under these circumstances.
Is this normal? Should I adjust my engine height?
Thanks for the input in advance!
The boat has a 200 HP Suzuki engine. I see 5800 RPM@ 45 MPH with a 18.5 Pitch Suzuki prop. The boat does porpoise around the upper 30's and above. This is with two people at the rear of the boat and nobody in the front lounges. Also, the 50 gallon fuel tank is near the rear of the boar in the center toon.
If I trim all the down (Negative trim) the boat does not porpoise at all under these circumstances.
Is this normal? Should I adjust my engine height?
Thanks for the input in advance!
- Attachments
-
- 7.jpg (432.86 KiB) Viewed 4226 times
-
- 6.jpg (517.59 KiB) Viewed 4226 times
-
- 5.jpg (396.89 KiB) Viewed 4226 times
-
- 4.jpg (470.56 KiB) Viewed 4229 times
-
- 3.jpg (442.09 KiB) Viewed 4226 times
-
- 2.jpg (396.11 KiB) Viewed 4226 times
-
- 1.jpg (450.73 KiB) Viewed 4225 times
-
- Posts: 1873
- Joined: Wed Nov 12, 2008 6:28 am
- Location: Iowa/Lake of the Ozarks, Mo.
- Contact:
Re: Engine Height For 200 HP Tritoon
Looks perfect where it is! I'd leave her alone. For a 30" PTX with a 200, looks like you are right where you should be.
Owner-EzFender Boat Products
Members, visit your discount page at:
http://www.ezfender.com/PontoonForums-M ... -Page.html
Members, visit your discount page at:
http://www.ezfender.com/PontoonForums-M ... -Page.html
-
- Posts: 52
- Joined: Fri Feb 24, 2017 9:17 pm
Re: Engine Height For 200 HP Tritoon
Thanks for the quick reply. Would you say my porpoising at high speed when not trimmed all the way down is the nature of the beast?
Re: Engine Height For 200 HP Tritoon
Yes any boat will begin to porpoise when trimmed too high...
As to height on transom it looks just right. It is generally desired to be able to see the anti cav plate while at speed and we can see yours...
As to height on transom it looks just right. It is generally desired to be able to see the anti cav plate while at speed and we can see yours...
T CRO
2017 Berkshire CTS 24 RFX with Yamaha F150/Simomized 200
2015 Caravelle 16 EBo with Mercury 90
2017 Berkshire CTS 24 RFX with Yamaha F150/Simomized 200
2015 Caravelle 16 EBo with Mercury 90
- rancherlee
- Posts: 580
- Joined: Tue Jul 13, 2010 5:59 am
- Location: Eveleth MN
Re: Engine Height For 200 HP Tritoon
If you can get it to porpoise then there is room to lift the engine higher BUT you may start loosing grip quicker while cornering. To me it looks mounted just right the way it is. My pontoon start to porpoise also when the trim gauge is halfway between level and the 1st positive mark, letting her bounce the bow a little gives me my best speed.
1988' Kennedy 20' "Haley's Comet"
Rebuilt 2016 with 25" single strake outer tubes and a 25x23" straked U-tube
2003 Suzuki DF140 - Yamaha 9.9HT kicker - 39.1@6300rpm
Rebuilt 2016 with 25" single strake outer tubes and a 25x23" straked U-tube
2003 Suzuki DF140 - Yamaha 9.9HT kicker - 39.1@6300rpm
Re: Engine Height For 200 HP Tritoon
Pontoons don't propose nearly as bad as fiberglass boats. But when they do, trim the engine down slightly for you most efficient cruise. Leave the height alone unless you have a serious ventilation as your rpm's are good.
'12 Bennington 24' SSLX Yamaha 150
Re: Engine Height For 200 HP Tritoon
I personally think you need to drop it one hole.
You want the motor plate even with the bottom of the center toon.
If you can change it easily do it and give it a test run.
You want the motor plate even with the bottom of the center toon.
If you can change it easily do it and give it a test run.
2012 SouthBay 722CRO 115hp Merc 4-stroke. Edit, make that a 150hp Merc 4-stroke now.
Re: Engine Height For 200 HP Tritoon
It's that danged water bottle. Loose it and all your porpoising will disappear 

Kenneth & Joy
Lake Conroe, Texas
2007 Bennington 2577RFSi
2006 Yamaha F225
Solas 14.25x17SS prop
Best ever top speed 69.2KPH
Lake Conroe, Texas
2007 Bennington 2577RFSi
2006 Yamaha F225
Solas 14.25x17SS prop
Best ever top speed 69.2KPH
-
- Posts: 52
- Joined: Fri Feb 24, 2017 9:17 pm
Re: Engine Height For 200 HP Tritoon
Thanks for your input everyone! I think I am going to leave well enough alone.